Raixer Mini Installation. List of requirements, tools and hardware

To connect the Raixer Mini to the intercom you will need:

• Your Raixer Mini and the connection cables included in the kit.
• Internet connection via WiFi at the installation point.
• A light point 1.5 meters from where you are going to install it.
• Multimeter
• Screwdriver
• Scissors
• Cable stapler

If you are going to carry out the assembly to control the opening of the house door and you do not already have a similar installation, you will also need:

• An electric door opener or lock without memory.
• 12V power supply
• Chisel and hammer to recess the door frame.

Prepare for a smooth installation

1. Check that the community doorman rings the apartment intercom.
2. Check that your intercom opens the front door when you press the open button.
3. Check that the microUSB cable reaches the socket from the point where you will install Raixer Mini.

Connecting Raixer Mini to the intercom

1. Raixer Mini has five outputs on each side. Each bay (P1, P2) is independent, so you can use them to operate two different doors. Below you have a connection diagram:

1. Pin 1: GND, ground or mass
2. Pin 2: Sensor
3. Pin 3: NO or normally open
4. Pin 4: COM or common
5. Pin 5: NC or normally closed
6. Use pins 1 and 2 of Raixer Mini to detect the voltage variation that occurs in the intercom when the doorbell is rung.
7. Use pins 3 and 4 of Raixer Mini to close the circuit and press the intercom button.
8. If you are going to connect it also to the electric door opener, use pins 3 and 4 on the side that is free to close the circuit of the electric door opener.
9. Open the intercom cover and locate the connection terminal. In the photo below, you will see a green terminal, with numbers and letters above each connector.

1. You will need to identify on that strip which outputs correspond to the open button, ground or mass, and the bell or sensor. You can check if your intercom is in these tables. If it is, you will save this step and can jump directly here.
2. If not, it does not mean that your intercom is not compatible! You will simply need a multimeter to locate them. We will tell you about it next.

Find the GND output

1. Connect the multimeter and activate the mode to measure continuous voltage.
2. Connect the black cable to the COM terminal of the multimeter and the red cable to VΩmA
3. Try all possible combinations between the intercom strip terminals until the multimeter shows the highest positive voltage.
4. If the voltage is negative, reverse the connection of the cables: connect the red where the black and the black where the red.
5. Connect the GND output of Raixer Mini to the terminal where the black multimeter cable is connected

Find the output to Sensor

1. Continue with the DC voltage measurement mode on the multimeter and do not disconnect the black wire.
2. Connect the red multimeter cable to each of the intercom terminals. It will show a constant voltage. If when you press the doorbell button, the voltage differential varies significantly, that is the sensor terminal.

You can connect output 2 of the Raixer device to any terminal, go down to the intercom with your mobile phone and check on the Raixer app device configuration screen the voltage variation when you press the doorbell. If the variation is notable, you will have found the terminal to which to connect output 2 of the Raixer device.

Find the outputs to NC and COM

The objective of these steps is to bridge the open button on your intercom. With this, you will be able to carry out the opening action both on the intercom and on Raixer Mini.

1. Connect the multimeter and activate the tester or beep mode and join the black and red wires, if the multimeter beeps, then it works correctly.
2. Locate the terminals of the intercom strip that correspond to the opening button plates.
3. Place the red or black cable on one of the intercom terminals and test on the other plates until the multimeter beeps. Repeat this step with the other terminal.
4. Check that these two terminals are correct: connect the multimeter cables to these two plates and press the opening button.
5. If the multimeter beeps, the connection will be correct.
6. If the multimeter does not beep, repeat the previous step until you locate the correct plates
7. Connect the NC and COM outputs of Raixer Mini to the two plates. The connection order does not matter.

Connecting Raixer Mini to the door opener or electric strike

1. Hollow out the door frame to embed the electric door opener.
2. Connect the electric door opener cables to the power source, according to the electrical specifications of these parts.
3. Connect the electric door opener to the NC and COM outputs of Raixer Mini.

Connecting Raixer Mini to the internet

1. Download the Raixer app for iOS or Android.
2. Create an account and confirm it.
3. Press Add > Configure new device > New WiFi Device
4. Follow the instructions that appear in the app.

Calibrating Raixer Mini for Auto Raixer Pro

Calibrating Raixer Mini correctly is necessary if you want to use the Auto Raixer Pro function or ring to open the portal. Calibration consists of making the device aware:

• What is the voltage existing in the intercom when no one is ringing the doorbell.
• What is the voltage when the doorbell rings?

Don't worry if you don't know what amps or volts are. The auto-calibration will guide you step by step so you can configure it correctly.

1. Press on the Raixer Mini you want to auto-calibrate.
2. Go to Settings > Doors > Edit, press on the door you use for Auto Raixer Pro, it will normally be the street door. Confirm.
3. Make sure that the port you are configuring is actually the one that Raixer Mini is connected to. On the Connect your door screen you will see a diagram of the device and an arrow indicating the port. They must match.
4. Press the Auto Calibrate button and follow the app instructions.

‍